micromaille - laucquering pliers?
View previous topic | View next topic >
Post new topic Reply to topic
M.A.I.L. Forum Index -> Knitting Circle
   
Author Message

Joined: December 29, 2004
Posts: 899
Submissions: 19
Location: North jersey

micromaille - laucquering pliers?
Reply with quote
Posted on Tue Apr 02, 2019 12:08 am
Link to Post: Link to Post

Hey all,

I'm currently doing a bit of micromaille using 28AWG silver, which understandably gets knocked around by my steel xuron pliers. I haven't found any nylon pliers that would work well - they're all too big and clunky to be of much use.

I've been taping the xurons with packaging tape, which works okay, but I'm curious if it would be a good idea to try some kind of lacquer (dip? spray? not sure) to insulate the silver from the steel prongs.

alternatively, if anyone has recommendations for good tiny nylon pliers or a better tape to use in this application, I'm all ears!

Joined: March 29, 2005
Posts: 505
Submissions: 26
Location: Plumstead, London

Reply with quote
Posted on Wed Apr 03, 2019 2:11 pm
Link to Post: Link to Post

felt/fabric tips. stitched (better) glued (in a pinch)

Joined: March 26, 2019
Posts: 3
Submissions: 0
Location: Colorado

Reply with quote
Posted on Sat Apr 06, 2019 3:30 am
Link to Post: Link to Post

I've used both plastic and rubber dipping agents on the handles of some of my tools in the past, and found it to be durable. I'm not sure how it would work on the business end of pliers, however... but it's cheap, so what do you have to lose? I'd look in the auto parts stores for such a substance, as it really is made for tools.

Joined: March 27, 2002
Posts: 3508
Submissions: 1

Reply with quote
Posted on Sat Apr 06, 2019 7:16 am
Link to Post: Link to Post

Plasti-Dip.
https://www.walmart.com/ip/Plasti-Dip-Tool-Handle-Coating/21015332?wmlspartner=wlpa&selectedSellerId=0&adid=22222222227016781835&wl0=&wl1=g&wl2=c&wl3=51770260391&wl4=pla-83188113311&wl5=9031625&wl6=&wl7=&wl8=&wl9=pla&wl10=8175035&wl11=online&wl12=21015332&wl13=&veh=sem&gclid=EAIaIQobChMIqoqqsfW64QIVICCtBh0TVwyGEAQYAiABEgJMBPD_BwE

Prices vary, so shop around.

Joined: December 29, 2004
Posts: 899
Submissions: 19
Location: North jersey

Reply with quote
Posted on Fri Apr 12, 2019 12:23 am
Link to Post: Link to Post

Konstantin the Red wrote:
Plasti-Dip.
https://www.walmart.com/ip/Plasti-Dip-Tool-Handle-Coating/21015332?wmlspartner=wlpa&selectedSellerId=0&adid=22222222227016781835&wl0=&wl1=g&wl2=c&wl3=51770260391&wl4=pla-83188113311&wl5=9031625&wl6=&wl7=&wl8=&wl9=pla&wl10=8175035&wl11=online&wl12=21015332&wl13=&veh=sem&gclid=EAIaIQobChMIqoqqsfW64QIVICCtBh0TVwyGEAQYAiABEgJMBPD_BwE

Prices vary, so shop around.


ah, i think this is what i was looking for.

Thanks for all the help and recommendations everyone! I've been labbing out how to get good closures and with dipped pliers i think I can avoid even more marring.

TL;DR of this project is a curb-chain of JPL in silver micromaille..I made a decent length of it a while ago but realized later that I can do better with the closures and the plier marks.

hope to have some good pictures to share soon!


http://chainmaillebookproject.ninjatails.com/index.php --Please contribute! Existing members, put this in your signature to increase publicity!

Joined: March 29, 2005
Posts: 505
Submissions: 26
Location: Plumstead, London

Reply with quote
Posted on Fri Apr 12, 2019 2:16 pm
Link to Post: Link to Post

We would love to see the ongoing work!

Ladies, Gentlemen? TO VICTORY!

Joined: May 27, 2019
Posts: 4
Submissions: 0
Location: Denver, CO

Reply with quote
Posted on Tue May 28, 2019 3:27 am
Link to Post: Link to Post

Another option that I've heard of but haven't tried is Tool Magic. (Available at most craft stores, usually cheaper than the current price on Amazon.)

Joined: March 29, 2005
Posts: 505
Submissions: 26
Location: Plumstead, London

Reply with quote
Posted on Tue May 28, 2019 1:44 pm
Link to Post: Link to Post

alissathorne wrote:
Another option that I've heard of but haven't tried is Tool Magic. (Available at most craft stores, usually cheaper than the current price on Amazon.)


So It's like an ablative coating? That's cool. You might have to watch that around new pliers. Those new pliers grip serrates can be quite choppy choppy. Still a really good idea if you have a spare set of warn pliers you can leave the coating on then periodically redip!

A MOST EXCELLENT FIND, m'lady!

Joined: March 27, 2002
Posts: 3508
Submissions: 1

Reply with quote
Posted on Thu May 30, 2019 6:26 am
Link to Post: Link to Post

If they're unduly gnawsey in the jawsey, take a small flat file to them and knock off the sharpness. This is simplest with the pliers clamped in a bench vise.


'The Minstrel Boy to the War is gone...'

Joined: March 29, 2005
Posts: 505
Submissions: 26
Location: Plumstead, London

Reply with quote
Posted on Thu May 30, 2019 9:27 am
Link to Post: Link to Post

Good point but it is a trade off, I do have some warn pliers that don't tend to mark, that said they are so warn that they do tend to slip. I'm currently running 2 plasters and one drying out scar on my right. (one of the knuckles I've done 3 times in the same place, pardon my language but it is a trifle effed.) Yes I should be wearing gloves but you know it's summer and I'm still building up my callouses (and scar tissue apparently).

Anyway to get back on track, pre-warn pliers all good, I would add that if possible only use on a weave where your going to get good area purchase on both sides of the link.

Going right back to your original post, nylon pliers. I wonder if we could 3d print something, and if your designing something from scratch you could design the "perfect" chainmaille pliers? You could make the chanmaille swiss army knife of pliers! With keys built into the metal, maybe a knuckle loop. I might start a thread. Very Happy

Joined: March 27, 2002
Posts: 3508
Submissions: 1

Reply with quote
Posted on Fri May 31, 2019 5:20 am
Link to Post: Link to Post

If it happens once more on the same knuckle, it'd be a -- quadruple effed. Coif Cool Smiley

Ran afoul of a kitchen rasp that way recently, zesting some lime peel. Bloody, that was. Lacerated, in a word. Still has a mark...

Joined: June 6, 2019
Posts: 30
Submissions: 0
Location: Brazil

Reply with quote
Posted on Tue Feb 18, 2020 10:03 pm
Link to Post: Link to Post

Konstantin the Red wrote:
Plasti-Dip.
Prices vary, so shop around.

This seems like such a nice and easy solution, unfortunately I can't get them around, and haven't heard of anything even similar, shipping would be too costly as well. Are the tips rubbery and do they last long?
For now at least I've found some fabric strengthened rubber tape, isn't the best but easy to replace.

Joined: March 3, 2002
Posts: 1013
Submissions: 244

Reply with quote
Posted on Wed Feb 26, 2020 11:17 pm
Link to Post: Link to Post

The tips are rubbery but they don't last very long. It's quite easy to re-dip them but it does take a while to dry. Your rubber tape may be a better solution.

I'm certain that there are similar products available in Brazil if not the same brand. Hardware stores should have some type of rubber coating for tool handles.


www.mailletec.com

Y'know, that might just be crazy enough to work!

Joined: March 27, 2002
Posts: 3508
Submissions: 1

Reply with quote
Posted on Sun Mar 01, 2020 6:26 am
Link to Post: Link to Post

Eh... we'll end up learning the Portuguese for 'tool dip.' Somebody ought to be supplying South America.


'The Minstrel Boy to the War is gone...'

Joined: June 6, 2019
Posts: 30
Submissions: 0
Location: Brazil

Reply with quote
Posted on Wed Mar 11, 2020 2:57 pm
Link to Post: Link to Post

Konstantin the Red wrote:
Eh... we'll end up learning the Portuguese for 'tool dip.' Somebody ought to be supplying South America.

You'd be surprise to see how hard it is to find some stuff, not only there is a lost in translation effect, the technical term being different, but also the popular slang for whatever it is, or even how to describe what the use is for.

Most of the things come around but the exception being very unique or newer things, besides that I'm practically restricted to the standard tool industry for jewelry, which is still relatively very small.

For example, I just found the other day some sort of acrylic glass varnish, on a simple paper store nearby, along side other varnishes used for painting/wood and etc, usual type of artisan work, this one though also works on metal, so it piqued my interest since I was having such a hard time to find any sort of metal jewelry sealant or anything of the like. However I failed to find any information on how to apply it properly. how to remove it, how long to dry... and practically already lost a brush to it.
This would be interesting to make it work, I'm trying on a brass ring right now, but I can see it also being useful to smooth out pliers.

Post new topic Reply to topic
Jump to:  
Page 1 of 1
All times are GMT. The time now is Sun Apr 05, 2020 10:12 am
M.A.I.L. Forum Index -> Knitting Circle
Display posts from previous: