Strongest Weave
Author Message
Dinwar

[ Major Voice ]

Joined: September 26, 2009
Posts: 500
Submissions: 0
Location: Meridies

Posted on Fri Mar 12, 2010 10:26 pm

For industrial/design purposes, this quote is also vital:

 Quote: Not only that but they are the only weaves that maintain full flexibility at near minimum AR's.

A chain that doesn't flex isn't all that useful. Maybe for static uses (say, hanging a birdhouse), but at that point you can save time/money buy just putting a wire up.

Out of curiosity (since we've ben discussing Japanese maille recently), when you say J4-1, you're refering the four small links connecting to each big link, correct? No doubling up or anything?

Joined: March 3, 2002
Posts: 1000
Submissions: 244

 Posted on Sat Mar 13, 2010 4:17 am Link to Post: Yes, 4 small links per 1 big link, additionally the AR's are tweaked so that the the strength of 2 small links is roughly equal to the strength of one large link. I think perhaps it was Ironband who was doing it? I'm probably wrong about that. It was discussed on one of the boards, and linked to a personal website but both appear to be gone now. I didn't keep any data handy and I don't remember much about it, but I'll see what I can dig up. www.mailletec.com Y'know, that might just be crazy enough to work!

Joined: March 3, 2002
Posts: 1000
Submissions: 244

 Posted on Sat Mar 13, 2010 6:24 pm Link to Post: OK, this should be the equation to calculate relative individual ring strength. F represents the amount of force that any one butted ring can withstand. If you want ultimate ring strength then you have to calculate the area moment of inertia seperately and multiply it by the Young's modulus of whatever material you are using. F=π^2(π/64(wire diameter^4))/((inner diameter+outer diameter)π/4)^2 The next step is to calculate, generally by counting, how many rings are in each horizontal row of the weave(or chain) per a set width at a set wire guage and minimum AR. Multiply F by the # counted to find the total force a sheet can withstand per area or a chain per length. You might want to calculate both per area and per weight values of each to find the strength:weight ratio of a finished piece of armor. Make sure that you are orienting each sheet in it's strongest direction, for instance e4-1 is strongest this way. ((((((((((((((((( ))))))))))))))))) ((((((((((((((((( ))))))))))))))))) ((((((((((((((((( J4-1 is strongest this way. .OOOOOOOOO VVVVVVVVVVV OOOOOOOOOO .VVVVVVVVVV .OOOOOOOOO www.mailletec.com Y'know, that might just be crazy enough to work!
Doing Nothing

[ Ringlet ]

Joined: March 13, 2010
Posts: 5
Submissions: 0
Location: Asheville, NC

 Strongest Weave ... Posted on Sun Mar 14, 2010 5:15 am Link to Post: If you are going to test the tensile strength of the maille, isn't that only one part of the true strength? In my experience, Maille is used to resist penetration and slashing more often than to hold weights off the floor. In this case, wouldn't you want to also for the penetration resistance and slashing resistance to form a three dimensional strength rating for Maille?

Joined: March 3, 2002
Posts: 1000
Submissions: 244

 Posted on Sun Mar 14, 2010 11:47 pm Link to Post: The resistance to deformation is very closely related to the resistance to shearing, the same model can be used to calculate both. In terms of a relative measure between weaves it is sufficient. In terms of the ultimate strength of real armour it's irrelevant. Any weave that is light and flexible and made out of quality materials will be protective enough. If you need more protection then you should be wearing plate armour. www.mailletec.com Y'know, that might just be crazy enough to work!
Dinwar

[ Major Voice ]

Joined: September 26, 2009
Posts: 500
Submissions: 0
Location: Meridies

 Posted on Mon Mar 15, 2010 12:57 am Link to Post: Yeah...And maille that protects against SCA blows is almost too heavy to fight in. I never knew that there was a strong and weak orientation to E4-1. It sort of makes sense, I just never considered it. Guess there's stuff still to learn about the simplest weaves!
diregriffon

[ Ringlet ]

Joined: January 19, 2016
Posts: 2
Submissions: 0

 lotsoquestions Posted on Tue Jan 19, 2016 9:04 pm Link to Post: Ok, IM new so please forgive any annoyance, As I have lots of questions. 1. what is an SCA hit? and can chainmail withstand it? 2. Can chainmail stop a bullet and if so what kind of padding is needed to prevent bones from braking? 3. I keep hearing about superior weaves that are really strong but not very flexible, would it be possible to use said on flexible weave, and then use a flexible weave for areas that need mobility? Final Question. If you were to line your chain mail with hard leather or place a plate over it (like the chest area, shoulders, and back) would that increase its overall effective ness. note> I found this thread through google so I apologize if I'm in the wrong spot with these questions.Ashesoffailure
Konstantin the Red

[ Uber Mouth ]

Joined: March 27, 2002
Posts: 3496
Submissions: 1

Konstantin the Red

[ Uber Mouth ]

Joined: March 27, 2002
Posts: 3496
Submissions: 1

 Posted on Wed Jan 20, 2016 3:57 am Link to Post: For Item 3, those are also very heavy. At that point, you're better beating out some plate using hammers rawhide-face split head hammers such as Thor or Garland Mfg. heavy wooden mallets homebuilt pile driver if you have a friend you can team up with a ratty old ruined bowling ball as your piledriver, suspended with bungee cords The Garlands, wood mallets, piledriver and bowling ball basherizer can all make a sheet of steel into a smoothly curved, rounded breastplate, the curves of large radius. Use, by various techniques, either a wood stump or an anvil's top. Water-hardened leather -- the method needs a very cool oven to do -- will protect very well from general impact hits just by itself and never mind any mail. Provides some resistance against sharp swords. Worthwhile if leather is all you can work. Also not cheap, though you can economize using leather that isn't perfectly top grade stuff. Water hardened leather can also be the basis of lamellar scales, so you can use scrap leather if you can get it thick enough -- little, cut-off pieces, with leather thongs attaching lame to lame to lame. Doesn't jingle.'The Minstrel Boy to the War is gone...'

Joined: August 30, 2008
Posts: 3138
Submissions: 20

Re: lotsoquestions
Posted on Wed Jan 20, 2016 2:24 pm

 diregriffon wrote: 2. Can chainmail stop a bullet and if so what kind of padding is needed to prevent bones from braking?

While we're at it... No, it won't.
What it will do, is add more shrapnel to the bullet wound. Broken bits of link, etc...

mithrilweaver

[ Grand Master Speaker ]

Joined: October 22, 2010
Posts: 730
Submissions: 390
Location: Yucaipa, CA

 Posted on Thu Jan 21, 2016 2:28 am Link to Post: i'm willing to take lorenzo's word that 2 in 1 chain is the strongest. but, i wonder why industrial chains don't use close to minimum ar? all the chains i've ever seen have large ars. isn't this sacrificing strength?http://www.joshuadiliberto.com
Konstantin the Red

[ Uber Mouth ]

Joined: March 27, 2002
Posts: 3496
Submissions: 1

 Posted on Thu Jan 21, 2016 2:46 pm Link to Post: It doesn't matter a great deal if the links are made with a crossbar across the middle of the link, anchor chain style. Those are the strongest chains around.'The Minstrel Boy to the War is gone...'
Karpeth

[ Grand Master Speaker ]

Joined: August 30, 2010
Posts: 774
Submissions: 33

Posted on Thu Jan 21, 2016 3:28 pm

 mithrilweaver wrote: i'm willing to take lorenzo's word that 2 in 1 chain is the strongest. but, i wonder why industrial chains don't use close to minimum ar? all the chains i've ever seen have large ars. isn't this sacrificing strength?

Most chains I have seen are oval, with low AR.

What makes me curious is why J4-1 would be strongest. I'd like to see the algorithmical comparison to E4-1, the only "real" competitor.

Total Nerd: MScDS, Mailler, Gamer.
Konstantin the Red

[ Uber Mouth ]

Joined: March 27, 2002
Posts: 3496
Submissions: 1

 Posted on Thu Jan 21, 2016 6:21 pm Link to Post: For a "telling SCA hit" to the helmet, here's how I do it, assuming I ever get back in the rattan game at my age and with foot troubles. A good hit to the helm is pretty loud, sometimes very loud, though it doesn't hurt your ears. Just a loud impact. The other part of it is, all right, it was noisy, now how far to the opposite side did this make my head roll? Pretty far over is enough, just a little bit I wouldn't count as a proper blow. This quality of sword blow power is judged by the recipient. It pays not to be stubborn about it -- always accept as fair, telling blows somewhat lighter than the blows you dish out. If your opponent landed one on you and you didn't take it, he's going to dial it up to hit you twice as hard next time. As you can tell, it therefore pays to stay reasonable. It also means not so many dents in your helmet. So, reasonable taking is helpful to armor maintenance. If you play in the SCA, you will log some hours of repair time every month; maintenance never ends. Good thing to have a fighter-buddy over to your place to chat while the two of you fix straps and stuff. It's usually straps, then rivets.'The Minstrel Boy to the War is gone...'
ClymAngus

[ Grand Master Speaker ]

Joined: March 29, 2005
Posts: 504
Submissions: 26

Posted on Fri Jan 22, 2016 11:49 am