exakt saw?
View previous topic | View next topic >
Post new topic Reply to topic
M.A.I.L. Forum Index -> Knitting Circle
   
Author Message

Joined: March 28, 2008
Posts: 386
Submissions: 0
Location: UK

exakt saw?
Reply with quote
Posted on Sat Oct 11, 2008 5:12 pm
Link to Post: Link to Post

anyone seen one of these before?

it's like a mini circular saw and fits small blades ( look about 35mm of so.. )

this would make an awesome ring cutter I'm thinking with the addition of the right thickness blade and some sort of jig to guide the blade and hold the coil..


"Hathor is the godess of fornication, intoxication and music..."
"So..... Sex, Drugs, and Rock 'n' Roll?"

Joined: August 10, 2005
Posts: 7098
Submissions: 337
Location: UK

Reply with quote
Posted on Sat Oct 11, 2008 5:47 pm
Link to Post: Link to Post

The kerf from that would be pretty terrible. A Dremel type saw set up would be a lot better.


Maille Code
V2.0 T7.3 R5.4 Ep Feur MAg/Cu Wm$ Cbjpw$ G0.5/3.0 I1.5/12.0 N322.150 Pajs Dacdjsw Xa7g631p4t24w64 S88 Hipsu

Joined: February 02, 2007
Posts: 1084
Submissions: 17
Location: England

Reply with quote
Posted on Sat Oct 11, 2008 6:31 pm
Link to Post: Link to Post

I see it... I sometimes do carpentry work so i was like mmmmmmmm.. Rolling Eyes
lol

Na but the Kerf would be too big...

Get a saw from The Ring Lord and get it fixed in a position for the drill so that it is securely down.

Joined: September 27, 2008
Posts: 14
Submissions: 0
Location: Owosso Michigan

Reply with quote
Posted on Sat Oct 11, 2008 7:18 pm
Link to Post: Link to Post

I think the fact that the rpms are so fast kinda kills it.
not to mention it would (as stated above ) take to much material.

Joined: March 28, 2008
Posts: 386
Submissions: 0
Location: UK

Reply with quote
Posted on Sat Oct 11, 2008 11:44 pm
Link to Post: Link to Post

did I not say above "with the right thickness blade"?

since it fits small saw blades, it's a safe bet you will find a 0.008" slitting blade (or whatever the thinest you can get ) that will fit it..

I think it would be better than a little bit of aluminium tube that you hold as a guard on the end of a flex shaft..?


"Hathor is the godess of fornication, intoxication and music..."
"So..... Sex, Drugs, and Rock 'n' Roll?"

Joined: June 26, 2008
Posts: 308
Submissions: 2

Reply with quote
Posted on Sun Oct 12, 2008 12:51 am
Link to Post: Link to Post

the speed is more of an issue than the blade, i think. harder metals require the lowest speed possible. 4000rpm wouldn't work.

Joined: June 02, 2007
Posts: 1523
Submissions: 9
Location: Bruges, Belgium

Reply with quote
Posted on Sun Oct 12, 2008 1:03 pm
Link to Post: Link to Post

Kahuna wrote:
the speed is more of an issue than the blade, i think. harder metals require the lowest speed possible. 4000rpm wouldn't work.


Yep, this would kill your blade in no time.


Horum omnium fortissimi sunt Belgae. [Of all these the Belgians are the bravest/strongest.]
- Gaius Iulius Caesar, De Bello Gallico I 3

Post new topic Reply to topic
Jump to:  
Page 1 of 1
All times are GMT. The time now is Sat Apr 04, 2020 7:03 pm
M.A.I.L. Forum Index -> Knitting Circle
Display posts from previous: