Search found 779 matches
M.A.I.L. Forum Index
Author Message
  Topic: Regarding angles in E4-1
Karpeth

Replies: 4
Views: 1416

PostForum: Articles Discussion   Posted: Mon Mar 23, 2020 10:13 am   Subject: Regarding angles in E4-1
The article is accurate for e4-1 at mid stretch. If you were to stretch a loose AR piece fully open the angle does approach 90 degrees but that's not practical for most applications. Similarly if you ...
  Topic: Regarding angles in E4-1
Karpeth

Replies: 4
Views: 1416

PostForum: Articles Discussion   Posted: Mon Mar 02, 2020 12:43 pm   Subject: Regarding angles in E4-1
I suppose I'd like to hear more about this.

Since I never found a solution for 40*, I Don’t remember How This concluded. I seldom use such sharp turns in my projects.
  Topic: Flowers in Cages AR
Karpeth

Replies: 3
Views: 113

PostForum: Weaves Discussion   Posted: Tue Jan 21, 2020 9:45 pm   Subject: Flowers in Cages AR
Then you should try somewhere around 4.5. Smile

Please reporter back with your results!
  Topic: Flowers in Cages AR
Karpeth

Replies: 3
Views: 113

PostForum: Weaves Discussion   Posted: Sun Jan 19, 2020 9:37 pm   Subject: Flowers in Cages AR
What number of rings are you using in the connector?
3.5 should be close to correct for 2 rings, 4.3 for 3 and 4.9 for 4. This is just a rough estimate.
  Topic: Beginner: What size rings should I use?
Karpeth

Replies: 6
Views: 200

PostForum: Knitting Circle   Posted: Wed Jan 15, 2020 1:34 am   Subject: Beginner: What size rings should I use?
The most historical WD in Sweden, I believe was 1.3mm.

8mm ID, 1.3mm WD. That’s a very good start, as it’d big enough and small enough.
  Topic: Date error?
Karpeth

Replies: 2
Views: 101

PostForum: M.A.I.L. Help   Posted: Wed Jan 15, 2020 1:16 am   Subject: Re: Date error?
My recent submissions are dated to 1969. I believe that is wrong.

Or have I invented a time machine? Wink

Usually indicates a problem server side, as that is the start of “UNIX Time”... Link m ...
  Topic: Newbie Introduction & Induction (Part the 3rd)
Karpeth

Replies: 166
Views: 13465

PostForum: Knitting Circle   Posted: Tue Jan 14, 2020 10:26 pm   Subject: Newbie Introduction & Induction (Part the 3rd)
Thanks for the Welcome Smile
So, where do you recommend for n00b advice?
Specifically, what size rings to use, and where to get them? UK here, so struggling to find a decent supplier. Will be investiga ...
  Topic: Newbie Introduction & Induction (Part the 3rd)
Karpeth

Replies: 166
Views: 13465

PostForum: Knitting Circle   Posted: Tue Jan 14, 2020 6:53 pm   Subject: Newbie Introduction & Induction (Part the 3rd)
Welcome!

We all hope you fond the community, forums and site to be welcoming and of good use!
  Topic: Date error?
Karpeth

Replies: 2
Views: 101

PostForum: M.A.I.L. Help   Posted: Mon Jan 13, 2020 9:58 pm   Subject: Date error?
My recent submissions are dated to 1969. I believe that is wrong.

Or have I invented a time machine? Wink
  Topic: Neural Networks and Chainmaille (Project Planning)
Karpeth

Replies: 9
Views: 1534

PostForum: Knitting Circle   Posted: Mon Jan 13, 2020 9:56 pm   Subject: Neural Networks and Chainmaille (Project Planning)
Have you had any further luck?
  Topic: Cutting rings with a flex shaft
Karpeth

Replies: 16
Views: 508

PostForum: Knitting Circle   Posted: Fri Jan 10, 2020 8:47 pm   Subject: Cutting rings with a flex shaft
The masking tape is probably a bad idea, the adhesive will clog the saw teeth and shorten the blade life, the paper has abrasive mineral fillers that cause extra wear. Try running beeswax over the coi ...
  Topic: The details
Karpeth

Replies: 5
Views: 168

PostForum: League Business   Posted: Wed Jan 08, 2020 4:00 pm   Subject: Re: The details
At that point we’ll hammer out some details, and get the appropriate permissions in place.

What happened?

Is There a hiccup, or anything keeping things from moving?

With 43 weaves in the ...
  Topic: The details
Karpeth

Replies: 5
Views: 168

PostForum: League Business   Posted: Wed Jan 08, 2020 12:21 am   Subject: The details
At that point we’ll hammer out some details, and get the appropriate permissions in place.

What happened?

Is There a hiccup, or anything keeping things from moving?

With 43 weaves in the ...
  Topic: Suggestion to (slightly) redesign the weave pages
Karpeth

Replies: 9
Views: 395

PostForum: Requests   Posted: Wed Jan 08, 2020 12:14 am   Subject: Suggestion to (slightly) redesign the weave pages
I could probably put together a chainmail weave family tree, but if I did, several items found in the MAIL library would have to be omitted.

Maybe next decade.

A family tree for Maille Would be ...
  Topic: Take this with a (Persian) grain of salt
Karpeth

Replies: 9
Views: 424

PostForum: Weaves Discussion   Posted: Wed Jan 08, 2020 12:11 am   Subject: Take this with a (Persian) grain of salt
The other grain is the same as what is used in gallery item

It appears as though FP Alt Twist is actually in the weaves library as

Nice find!

We should make a full list of these, more avai ...
 
Page 1 of 52 Goto page 1, 2, 3 ... 50, 51, 52  Next
All times are GMT
Jump to: